25.4-mm mirror mount, stainless steel, high-stability, front-loading, 2 hex adjusters
MHX-25.4A
Higher moment of inertia to maximize stiffness and faster to reach thermal equilibrium characteristics are achieved by a hollow-frame design. Ideal for interference measurement or precision measurement.
Please check for an introduction video of the structure and features of MHX.
Please check for an introduction video of the structure and features of MHX.
◦In the case of MHX-25.4F-R, Insert the mirror from the back and fix it when the mirror's reflective surface hits the mirror frame . As a result, the mounting center of the rod and the reflecting surface of the mirror can always be matched even if the thickness of the mirror changes.
◦MHX-25.4F/F-R has three adjustment screws to adjust not only tilt and rotation but also reflective surface the back and forth. The MHX-25.4A has only two adjustment screws to adjust only tilt and rotation.
◦Equipped with bonding holes for mirror bonding and pin holes for rotation prevention and positioning.
◦High-density stainless steel is used for the material, but the weight has been reduced by reducing the thickness.
◦The thickness of the frame is made thinner and follows immediately even if the temperature changes, and the distortion of the frame due to the temperature distribution is kept low.
◦MHX-25.4F/F-R has three adjustment screws to adjust not only tilt and rotation but also reflective surface the back and forth. The MHX-25.4A has only two adjustment screws to adjust only tilt and rotation.
◦Equipped with bonding holes for mirror bonding and pin holes for rotation prevention and positioning.
◦High-density stainless steel is used for the material, but the weight has been reduced by reducing the thickness.
◦The thickness of the frame is made thinner and follows immediately even if the temperature changes, and the distortion of the frame due to the temperature distribution is kept low.
| Name | 25.4-mm mirror mount, stainless steel, high-stability, front-loading, 2 hex adjusters |
|---|---|
| Weight | 0.1600kgs |
| Guide |
In addition, a special screwed knob (MHX-K-M6) is also available instead of the hexagon wrench.
|
| Attention |
|
| Optic Loading Side | Front Loading |
| Angle Range | ±3° |
| Material | Stainless Steel |
| Number of Control Axes | 2 points |
| Optic Diameter | φ25.4mm |
| Mount Material | Stainless Steel |
| Compatible Optics Diameter | φ25, φ25.4mm |
| Compatible Optics Thickness | 3 - 6mm |
| Mirror Clamping Mechanism | Set Screw with Torsion Barrier, 2-mm (5/64-in.) Hex Key |
| Recommended Mirror Clamping Torque | 0.07±0.01 Nm (10±2 oz.-in.) |
| Number of Adjustment Axes | 2 points |
| Angular Travel Range | ±3° |
| Adjuster Thread | M6 x 0.250mm(~100 TPI) |
| Standardized Adjustment Sensitivity (based on 1° knob rotation) | 20 μrad |
| Typical Adjustment Sensitivity | 6±2 μrad |
| Dowel Pin Keys | ɸ2mm Slot and Hole |
| Standard Mounting | Counterbored clearance hole for M4 / 8-32 screws |
| Center-Post Mounting | M4 and 8-32 threaded holes |
| Thermal Repeatability with a Δ10°C Thermal Cycle | ≤1.5 μrad |
Out of stock
SKU
MHX-25.4A
€112.20
Customize product
Higher moment of inertia to maximize stiffness and faster to reach thermal equilibrium characteristics are achieved by a hollow-frame design. Ideal for interference measurement or precision measurement.
Please check for an introduction video of the structure and features of MHX.
Please check for an introduction video of the structure and features of MHX.
Resources & Downloads
Related Products
Check items to add to the cart or
