Outer Dimension Tolerance and Standard Chamfer Company Standard
All products produced by Sigma Koki are inspected with valid metrology instruments that have supporting traceability. Instruments and supporting equipment in our metrology department are calibrated by their respective manufacturers or certified laboratories. Our maintenance program ensures that the level of accuracy is always at optimum levels. It is possible to request for a Calibration Inspection Certificate for the metrology instrument used against any of our products inspected. (Please note that that will be a small fee for this request)
Optical Flats | Optical Parallels | Wedged Substrates | Concave Mirror and Substrates (Applies to Other Standard Coated Optics Also)
Outer Dimension Tolerance (mm)
Round Shaped
Dimension Tolerance
Thickness Tolerance
φ50
0 to -0.1
±0.1 (Concave mirror and its substrate is +/-0.2)
φ51 to 150
0 to -0.2
±0.2
φ151 to 200
0 to -0.3
±0.3
φ201 to 300
0 to -0.5
±0.5
* Tolerance of center thickness for standard Concave mirror and its substrate is +/－0.2
Square or Rectangular Shaped
Dimension Tolerance
Thickness Tolerance
<=50
0 to -0.1
±0.1 (Concave mirror and its substrate is +/-0.2)
51 to 150
0 to -0.2
±0.2
151 to 200
0 to -0.3
±0.3
201 to 300
0 to -0.5
±0.5
* Outside tolerance of 50×60 size is 0 to -0.2
Standard Chamfer (mm)
Thickness
Dimension
Standard Chamfer
1.0 to 3.0
Specify
<=0.3×45°
3.1 to 5.0
<=40
<=0.3×45°
41 to 70
<=0.4×45°
71 to 100
<=0.5×45°
101 to 150
0.2 to 0.6×45°
151 to 200
0.3 to 0.7×45°
201 to 300
0.4 to 0.8×45°
<=5.1
<=40
<=0.3×45°
41 to 70
<=0.4×45°
71 to 100
<=0.5×45°
101 to 150
0.3 to 0.7×45°
151 to 200
0.4 to 0.8×45°
201 to 300
0.5 to 1×45°
Caution1: Chamfer of concave mirror is identical to Spherical Lens. Caution2: Chamfer finish is for protection to suffer from chipping, and the amount of chamfer may vary.
Spherical Lens | Cylindrical Lens
Outer Dimension Tolerance (mm)
Size
Dimension Tolerance
<=60
0 to -0.1
61 to 80
0 to -0.15
81 to 100
0 to -0.2
101 to 200
0 to -0.25
201 to 300
0 to －0.3
Standard Chamfer (mm)
Diameter
Standard Chamfer
Convex-side
<=50
<=0.3×45°
51 to 100
<=0.4×45°
101 to 150
<=0.5×45°
151 to 200
0.3 to 0.6×45°
201 to 300
0.4 to 0.7×45°
Concave-side, Flat-side
<=50
<=0.3×45°
51 to 100
<=0.5×45°
101 to 150
0.3 to 0.6×45°
151 to 200
0.4 to 0.8×45°
201 to 300
0.6 to 1×45°
* Some standard parts has other tolerance than above data.
Prism
About Outer Dimension Tolerance
Prisms have sharp edges because of its function and therefore usually needs protective bevels. Outer dimensions of prisms are noted by length without bevels.
We detect that you are accessing the website from a different region. You will be redirected to a local version of OptoSigma.
